Position: Index >

Mains Remote-Alert circuit (BZX79C30)

2016-02-21 07:50  
Declaration:We aim to transmit more information by carrying articles . We will delete it soon, if we are involved in the problems of article content ,copyright or other problems.

Beeper and/or LED remotely-operated via mains supply line

Transmitter circuit diagram:

Mains Remote-Alert Transmitter

Transmitter parts:

R1____________220K   1/4W Resistor
R2____________470R   1/2W Resistor
R3____________100K   1/4W Resistor
R4______________1K   1/4W Resistor

C1_____________10nF  400V Ceramic or Polyester Capacitor
C2____________330nF  400V Polyester Capacitor
C3______________1n5   63V Ceramic Capacitor (See Notes)
C4_____________10nF   63V Ceramic or Polyester Capacitor
C5____________100µF   25V Electrolytic Capacitor

D1,D2________1N4007 1000V 1A Diodes
D3_________BZX79C30   30V 500mW Zener Diode

Q1,Q2_________BC546   65V 100mA NPN Transistors

L1_______________IF Transformer for AM receivers, 445-470KHz

P1_____________SPST Mains suited Pushbutton

PL1____________Male Mains plug & cable

This article introduces the Mains Remote - Alert circuit (BZX79C30). The content is very simple, but very useful. An understanding of the components in the article can help you better understand the article. In this article, for example, you can go to understand and purchase these components:BZX79C30.


Receiver circuit diagram:

Mains Remote-Alert Receiver

Receiver parts:

R1____________220K   1/4W Resistor
R2____________470R   1/2W Resistor
R3____________150K   1/4W Resistor
R4______________2K2  1/4W Resistor
R5____________100K   1/4W Resistor
R6_____________47K   1/4W Resistor
R7______________2K2  1/4W Resistor (Optional)

C1____________100nF  400V Polyester Capacitor
C2____________330nF  400V Polyester Capacitor
C3______________1n5   63V Ceramic Capacitor (See Notes)
C4,C6_________330pF   63V Ceramic Capacitors
C5,C7_________100µF   25V Electrolytic Capacitors

D1,D2________1N4007 1000V 1A Diodes
D3_________BZX79C12   12V 500mW Zener Diode
D4,D5,D6_____1N4148   75V 150mA Diodes
D7_____________5mm. Red LED (Optional)

Q1,Q2_________BC547   45V 100mA NPN Transistors

L1_______________IF Transformer for AM receivers, 445-470KHz

BZ1___________Piezo sounder (incorporating 3KHz oscillator)

PL1____________Male Mains plug & cable

Pressing the pushbutton of the transmitter, a sound and/or light alert is activated in the receiver. The system uses no wiring or radio frequencies: the transmitted signal is conveyed into the mains supply line. It can be used at home, in any room from attic to cellar, simply plugging transmitter and receiver in the wall mains sockets. Transmission range can be very good, provided both units are connected to the mains supply within the control of the same light-meter.

Q1 and Q2 are wired as a Darlington pair to obtain the highest possible output from a Hartley type oscillator running at about 135KHz frequency. The 230Vac mains is reduced to 30Vdc without the use of a transformer by means of C2 reactance, a two diode rectifier cell D1 & D2 and Zener diode D3.
The oscillator output is taken from L1 secondary winding and injected into the mains wiring by means of C1.

The 135KHz sinewave generated by the transmitter is picked-up from mains wiring by C1 and selected by the tuned circuit L1-C3. Q1 greatly amplifies the incoming sinewave and converts it in a 12V-peak squarewave. D4 & D5 limit the input voltage at Q1 base to less than 1V-peak to avoid damaging of the transistor due to the high voltage transients frequently occurring on the mains line. D6 eliminates any negative component of the signal and Q2 drives the load. C7 is necessary to smooth the signal residues appearing across the load.
The 12Vdc supply for this unit is obtained as described above for the transmitter circuit.

 


Reprinted Url Of This Article:
http://wiringdiagramcircuit.com/mains-remote-alert/