Position: Index > Amplifier Circuit >

150 Watt amplifier circuit

2015-01-02 13:50  
Declaration:We aim to transmit more information by carrying articles . We will delete it soon, if we are involved in the problems of article content ,copyright or other problems.

Low Cost 150 Watt Amplifier Circuit


This is the cheapest 150 Watt amplifier circuit you can get,I think.Based on two Darlington power transistors TIP 142 and TIP 147 ,this circuit can deliver a blasting 150 W Rms to a 4 Ohm speaker.Enough for you to get rocked?,then try out this.

TIP 147 and 142 are complementary Darlington pair transistors which can handle 5 A current and 100V ,famous for their ruggedness. Here two BC 558 transistorsQ5 and Q6 are wired as pre amplifier and TIP 142 ,TIP 147 together with TIP41? (Q1,Q2,Q3)? for driving the speaker.This circuit is designed so rugged that this can be assembled even on a perf board or even by pin to pin soldering.The circuit can be powered from a /-45V 5A? dual power supply.You must try this circuit.Its working great.

The preamplifier section of this circuit is based around Q4 and Q5 which forms a differential amplifier. The use of a differential amplifier in the input stage reduces noise and also provides a means for applying negative feedback. Thus overall performance of the amplifier is improved. Input signal is applied to the base of Q5 through the DC decoupling capacitor C2. Feedback voltage is applied to the base of Q4 from the junction of 0.33 ohm resistors through the 22K resistor. A complementary Class AB push-pull stage is built around the transistors Q1 and Q2 for driving the loud speaker. Diodes D1 and D2 biases the complementary pair and ensures Class AB operation. Transistor Q3 drives the push-pull pair and its base is directly coupled to the collector of Q5.

Circuit Diagram & Parts List .

150 watt amplifier
150 watt amplifier circuit diagram


    Remember TIP 142 and 147 are Darlington pairs? .They are shown as conventional transistors in figure for ease.So don’t get confused.Even though each of them have 2 transistors ,2 resistors and 1 diode inside ,only three pins ,base emitter and collector are coming out.Rest are connected internally.So its quite OK to assume each of them as transistor for ease.Use a well regulated and filtered power supply.Connect a 10K POT in series with the input as volume control if you need.Not shown in circuit diagram.All electrolytic capacitors must be rated at least 50volts.

    Power supply for this circuit.

    A? 40/-40 unregulated dual supply for powering this amplifier project is shown below.? This power supply is only enough for powering one channel and for stereo applications double the current ratings of? the transformer, diodes and fuses.

    amp supply

    Power supply for this project


    TIP 142 & 147 Internal diagram and pin out.

    TIP 142-TIP 147 Pin Out Diagram and Schematics

    TIP 142-TIP 147 Pin Out Diagram with Schematics

    We have more related list of? Amplifier Circuits that you may like to visit;

    1. 2 X 60 Watts Stereo Amplifier Circuit –is designed using LM4780, an audio amplifier IC that can deliver 60 Watt RMS output power per channel to? 8 Ohms speakers.? Advantages of using this IC are low harmonic distortion compared to other IC amplifiers of similar category and a power supply rejection rate of 85db. In addition it require minimum components and a built in mute function.

    2. Headphone Amplifier Circuit –This is a simple circuit which uses only 3 transistors, that can be used to drive your headphone. It can be easily built by any one and can be powered using a 3 volts battery.?

    3. Mosfet Amplifier Circuit -This circuit is designed using two Mosfet’s and one transistor; which makes it an easy to build circuit. It can deliver 18 Watts output power to 8 ohms speaker or 30 watts to 4 ohms speaker; you can do it the way you like it. Another advantage of this circuit is the minimal use of components.

    4. 40 Watts Amplifier using TDA1514 -TDA1514 is a high performance hi – fi amplifier from Philips. It requires a dual 25/-25 volts supply. Advantages of using TDA1514 are low THD, mute standby feature, thermal protection and other features. It can deliver 40 watts of output power to an 8 ohm speaker. You need a proper heat sink for the desired reliability of this circuit.

    5. 2 X 32 Watts Stereo Amplifier Circuit –This circuit is built using TDA2050 which is a 32 Watts Class AB Audio amplifier IC (monolithic) . This IC has many features like thermal shut down, low THD, short circuit protection etc. This circuit uses Two of these IC TDA205o; one for each channel.? An 18 volts dual power supply is required to power this circuit.

    Reprinted Url Of This Article: