Position: Index > Amplifier Circuit >

Stereo Preamplifier With Bass-boost electronic circuit diagr

2015-01-05 12:38  
Declaration:We aim to transmit more information by carrying articles . We will delete it soon, if we are involved in the problems of article content ,copyright or other problems.
Stereo Preamplifier with Bass-boost electronic circuit diagram

High Quality, simple design 20 to 30V supply

Parts:

P1_________________10K Log.Potentiometer (Dual-gang for stereo)
P2________________100K Log.Potentiometer (Dual-gang for stereo) (See Notes)
R1,R2_____________100K 1/4W Resistors
R3,R6______________15K 1/4W Resistors
R4_________________10K 1/4W Resistor
R5_________________22K 1/4W Resistor
R7__________________1K 1/4W Resistor
R8________________560R 1/4W Resistor
C1,C2,C5____________2΅2 63V Electrolytic Capacitors
C3________________470΅F 35V Electrolytic Capacitor
C4__________________1΅F 63V Polyester Capacitor
C6_________________47nF 63V Polyester Capacitor
C7_________________22΅F 25V Electrolytic Capacitor
IC1_______________TL072 Dual BIFET Op-Amp
SW1________________DPST Switch (Optional, see Notes)

Comments:

This preamplifier was designed to cope with CD players, tuners, tape recorders etc., providing a gain of 4, in order to drive less sensitive power amplifiers. As modern Hi-Fi home equipment is frequently fitted with small loudspeaker cabinets, the bass frequency range is rather sacrificed. This circuit features also a bass-boost, in order to overcome this problem. You can use a variable resistor to set the bass-boost from 0 to a maximum of 16dB @ 30Hz. If a fixed, maximum boost value is needed, the variable resistor can be omitted and substituted by a switch.

Notes:

* Schematic shows left channel only, but R1, R2, R3 and C1, C2, C3 are common to both channels.
* For stereo operation P1, P2 (or SW1), R4, R5, R6, R7, R8 and C4, C5, C6, C7 must be doubled.
* Numbers in parentheses show IC1 right channel pin connections.
* A log type for P2 ensures a more linear regulation of bass-boost.
* Needing a simple boost-in boost-out operation, P2 must be omitted and SW1 added as shown in the diagram.
* For stereo operation SW1 must be a DPST type.
* Please note that, using SW1, the boost is on when the switch is open, and off when the switch is closed.

Technical data(30V supply):

Gain @ 1KHz: 4
Max. input voltage @ 50Hz: 500mV RMS (280mV RMS @ 20V supply)
Max. input voltage @ 100Hz: 700mV RMS (460mV RMS @ 20V supply)
Max. output voltage: >8V RMS (>5V RMS @ 20V supply)
Max. bass-boost referred to 1KHz: 400Hz = 2dB; 200Hz = 5dB; 100Hz = 10dB; 50Hz = 14dB; 30Hz = 16dB
Total harmonic distortion @ 100Hz and 1V RMS output: 0.02%
Total harmonic distortion @ 1KHz and 1V RMS output: 0.006%
Total harmonic distortion @10KHz and 1V RMS output: 0.007%
Total harmonic distortion @ 100Hz and 5V RMS output: 0.02%
Total harmonic distortion @ 1KHz and 5V RMS output: 0.0013%
Total harmonic distortion @10KHz and 5V RMS output: 0.005%
Current drawing: 2mA

Source: Electronics Lab













































Reprinted Url Of This Article:
http://www.free-circuits.com/circuits/audio/134/stereo-preamplifier-with-bass-boost