Position: Index > Simple Circuit >

Simplest FM Transmitter

2015-01-10 21:10  
Declaration:We aim to transmit more information by carrying articles . We will delete it soon, if we are involved in the problems of article content ,copyright or other problems.
Simplest FM Transmitter

 

Simplest FM Transmitter

 


This simple FM Transmitter takes audio input through a 1/4" phono jack and, constructed as shown, without the optional antenna connections, will broadcast an FM radio signal about 30 feet. This is the standard model of simplest FM transmitters includes a trim capacitor to adjust the transmitting frequency. It can be powered by a 9V battery and uses a hand-turned copper coil. The circuit is extraordinarily simple and could be built on perfboard or on a panel almost as easily.


Simplest FM Transmitter

Simplest FM Transmitter Parts
Copper wire (4 inches), enameled, solid, 19 AWG or 20 SWG
1/4" TRS jack, AKA "phono jack" Only tip and shield connections are used.
Battery holder clips, 9V, with 4" leads
PCB, bought or home-etched or use perfboard and jumpers.
Double-sided foam tape (1.5")
Battery, 9V
Mini trim capacitor, 20 p?
Ceramic capacitor, 10 p?
Ceramic capacitor (2), 0.01 μ?
NPN silicon transistor, BC337
Electrolytic capacitor, 1 u?
Metal film resistor, 470 Ohm
Metal film resistor, 10 K Ohm
Metal film resistor, 27 K Ohm
Multistrand hookup wire (8"), 24 AWG


Form coil
Take a piece of 19 AWG enameled copper wire, about 4" long, and wind at least four turns about the threads of a 1/4-20 bolt or machine screw.
Rotate the bolt counterclockwise to unscrew the coil from the thread.
You want a total of four turns in the coil. Use small pliers to bend two legs down, as shown, and side-cutting pliers to clip them to about 1" long.
The mounting holes for the coil legs should be 12mm apart on the surface of the PCB. The act of installing the coil on the board should stretch it to the correct length, but you may have to tweak it a bit with pliers or a screwdriver to make sure the rate of coiling is even between the two legs.


Install components
Bend and slip the component leads into the correct holes in the PCB.
Carefully note and verify the correct orientation of the electrolytic capacitor and wire leads.
Bend the leads on the solder side of the board to temporarily secure the components in place. Clip them to about 1/4" to open up a bit of room to solder in.


Solder components
Clip the PCB, trace-side up, into your helping hands, or otherwise secure it, in a level horizontal orientation.
As always when soldering, be sure to work with plenty of ventilation and avoid inhaling fumes.
Flux, heat, and solder each lead in place.
Once the solder has cooled, clip any protruding leads with side or end-cutting pliers.


Mount PCB
Mounting details will naturally vary with the case you choose. This foam-tape method worked great for my salvaged clock case, but your mileage may vary.
Attach a strip of double-sided foam tape to the featureless corners of the PCB, on the trace side, as shown. Each strip is about 1/4 x 3/4".
Do not attach tape directly over the traces, or you may damage them if you ever have to remove the tape.
Remove the backing from the foam tape strips on the PCB.
Making sure the leads are first correctly positioned, carefully orient the PCB and press it into place.


Tune circuit
Connect a fresh 9V battery to the battery clip, and an audio signal to the TRS jack. I used the headphone jack of my laptop for an audio source.
Turn on your FM radio, and scan around looking for your signal. I found mine at around 99.8 MHz. It may be quite static-y and noisy at first.
Use a small screwdriver to adjust the trim capacitor, as shown, until your signal comes through loud and clear.


Assemble
Remove the washer and nut from the phono jack and thread it, from inside the case, through the hole you drilled in Step 1.
Put the washer over the threads and tighten the nut down from outside the case, to secure the jack. Finger-tight is fine.
Attach a 9V battery to the clip, pad it with a scrap of bubble wrap, and stuff it in the case before sealing up.
I'm going to to modify my transmitter with a jack for an external regulated power supply. You may want to do the same, or at least add a power switch between the battery and the board. But for testing purposes, this set-up will suffice.


Simplest FM Transmitter

Simplest FM Transmitter

Simplest FM Transmitter

Simplest FM Transmitter































Reprinted Url Of This Article:
http://electronics-diy.com/simplest-fm-transmitter.php