Position: Index > Unclassified >

A Very Useful Timed Beeper Circuit(CD4081)

2017-08-06 17:27  
Declaration:We aim to transmit more information by carrying articles . We will delete it soon, if we are involved in the problems of article content ,copyright or other problems.

This article describes the A Very Useful Timed Beeper Circuit (CD4081). The principle is very simple, very practical. The circuit components can help you understand better grasp this principle. For example, in this circuit, you can go to find and buy these components: CD4081.

Beeps 7.5 seconds after a preset time, Adjustable time settings: 15s. 30s. 1min. & others

This circuit is intended for alerting purposes after a certain time is elapsed. It is suitable for table games requiring a fixed time to answer a question, or to move a piece etc. In this view it is a modern substitute for the old sandglass. Useful also for time control when children are brushing teeth (at least two minutes!), or in the kitchen, and so on.

Circuit diagram:

Figure:1 Timed Beeper Circuit Diagram

Figure 1 Timed Beeper Circuit Diagram

Parts:

R1 = 220R
R2 = 10M
R3 = 1M
R4 = 10K
R5 = 47K
C1 = 100nF-63V
C2 = 22μF-25V
D1 = 1N4148
D2 = 3mm. RedLED
Q1 = BC337
P1 =SPSTPushbutton (Start)
P2 =SPSTPushbutton (Reset)

PS = Piezo sounder (incorporating 3KHz oscillator)
B1 = 3V Battery (2 AA 1.5V Cells in series)
IC1 = CD4081 Quad 2 inputANDGate IC
IC2 = CD4060 14 stage ripple counter and oscillator IC
SW1 = 4 ways Switch (See notes)

Circuit operation:

Pushing on P1 resets IC2 that start oscillating at a frequency fixed by R3 & C1. With values shown, this frequency is around 4Hz.LEDD2, driven by IC1A & B, flashing at the same oscillator frequency, will signal proper circuit operation. SW1 selects the appropriate pin of IC2 to adjust timing duration:
Position 1 = 15 seconds
Position 2 = 30 seconds
Position 3 = 1 minute
Position 4 = 2 minutes
When the selected pin of IC2 goes high, IC1C drives Q1 and the piezo sounder beeps intermittently at the same frequency of theLED. After around 7.5 seconds pin 4 of IC2 goes high and IC1D stops the oscillator through D1. If you want to stop counting in advance, push on P2.

Notes:
SW1 can be any type of switch with the desired number of ways. If you want a single fixed timing duration, omit the switch and connect pins 9 & 13 of IC1 to the suitable pin of IC2.

The circuit’s reset is not immediate. Pushing P2 forces IC2 to oscillate very fast, but it takes some seconds to terminate the counting, especially if a high timer delay was chosen and the pushbutton is operated when the circuit was just starting. In order to speed the reset, try lowering the value of R5, but pay attention: too low a value can stop oscillation.

Frequency operation varies with different brand names for IC2. E.g. Motorola’s ICs run faster, therefore changing of C1 and/or R3 values may be necessary.

You can also use pins 1, 2, 3 of IC2 to obtain timings of 8, 16 and 32 minutes respectively.

An on-off switch is not provided because when off-state the circuit draws no significant current.

 

 


Reprinted Url Of This Article:
http://www.eeweb.com/blog/extreme_circuits/a-very-useful-timed-beeper-circuit-schematic