﻿ Boosting Regulator Current for IC (MJ2955)_Circuit Diagram World ﻿
Position: Index >

# Boosting Regulator Current for IC (MJ2955)

2017-07-02 09:53
Declaration:We aim to transmit more information by carrying articles . We will delete it soon, if we are involved in the problems of article content ,copyright or other problems.

This article describes the Boosting Regulator Current for IC (MJ2955). The principle is very simple, very practical. The circuit components can help you understand better grasp this principle. For example, in this circuit, you can go to find and buy these components:MJ2955.

Normally 78xx series ICs can be output currents for a maximum 1 A, or in the common usage, it is only up to 0.6A.
But we need more boost current up, how to do next″
In this increasing Regulator Current or circuit, the power transistor is used to provide most current to the load, to maintain a constant the voltage, by the little current still through the regulator IC intact.
Let’s say, I want a the 12V voltage regulator, and current output voltage at 5A, I must to use an IC No. 7812 and it can take a transistor number MJ2955 or TIP2955. The input voltage is enough I think that about 20V, which voltage drop across the transistor is approximately 8V. And it takes about 40Watt energy, which can be calculated = Vce * Ic. When is this. We need a cooling pad for Q1, which is large enough, it is very hot, may be cause damage.
If you want to add current to the IC 79xx or negative voltage, you can also easy to make, but simple NPN transistor type 2N3055 is only a number.

But this circuit not have protection over load
Sometimes we want to use. high current at a voltage 5 volts.We can do this by using the voltage regulator IC1 positive constant number 7805.
The Q1-2N3792and Q2-2N5956of circuit will serve to increase current for IC regulator.The R2 acts as the anti-saturation of Q12N3792and Q2-2N5956. Without R2 will allow the two transistors do not work.The output current can be from IC1 alone.R1 specify the bias current to IC1.And the current output of you against too much saturated with. The C1 functions in input power filter to smooth.And C2 serves to prevent interference with the pressure to pay out (Vout).

This circuit can help enlarge current of power supply circuit that use Ic regulator so well. you can use other IC 7805,7809,IC-7812,and IC7815.
Q1 isBFX88or Equivalent
Q2 isBD132or Equivalent

You may also like these contents.
Current Booster circuit
Increasing Regulator Current
High Current Variable Voltage Regulator 2-36V 10AYesterday I no enhance the circuit in my blog. Today lead High Current power supply 10A and Can Adjustable Voltage or Variable Voltage Regulator 2V to 36V. By the prominent point of this circuit. Be there is the a little equipment and is simple have VR1 for control Volt output.[...]
Increase output current of the op-amp IC LM324 in 85mA size The op amp output current can generally be in the range of 20 to 40mA.However, the LM324 IC number includes op amp 4 and 3 per parallel.Therefore the output currents up to 85mA, it also has significant short-circuit protection too.[...]
High current 12V 30A,25A,20A,15A ham radio power supply Essential for those who want to use the radio transmitters from a car to use in your home is you need a ham radio power supply DC-12V or DC-13.8V with enough power out of 5A to 30A. According to size of the a transmitter.[...]

Reprinted Url Of This Article:
http://wiringdiagramcircuit.com/boosting-regulator-current-for-ic-78xx-by-mj2955/
Maybe you like
﻿