Position: Index > Unclassified >

IC PROG Programmer Settings and programming PIC

2017-12-21 17:50  
Declaration:We aim to transmit more information by carrying articles . We will delete it soon, if we are involved in the problems of article content ,copyright or other problems.

IC Prog Prototype Programmer software


IC PROG Settings for PIC Programmer and programming PIC Using .HEX file

IC PROG Settings for JDM PIC Programmer

Download IC Prog SoftwareStart the IC Prog SoftwareGo Settings → Hardware (F3)

You need the following settings in IC Prog, (select JDM Programmer and Windows API)

IC Prog Programmer hardware menu settings

Note: If you have more ports you need to select correct com port.

When using NT, 2000, XPyou need Installing Driver

Download the Windows NT/2000/XP Driver. Put the NT/2000 driver file (icprog.sys) in the same directory as the ICProg.exe file. In ICProg, click on‘Settings’in the main window and open the‘Options’window. Select the ‘Misc‘ tab. Click ‘Enable NT/2000/XP Driver‘. ICProg will then restart with the new driver and everything should be peachy.

IC Prog Installing Driver for NT, 2000, XP

When using Vista and Windows 7you need to installing IC Prog 1.06.

Configure Ic-prog Smartcard tab

In ICProg, click on‘Settings’in the main window and open the‘Options’window. Select the ‘Smartcard‘ tab.

Example: You need the following settings when using PIC16F84 or PIC18F84A

ic-prog smartcard setting for pic16f84

Configure the serial port in Computer

Go to the Device Manager (Start→Settings→Control Panel→Device Manager)

Ports (Com & LPT)→Double click on communications port (Com 1 or 2 )→Port
configuration tab

com port configuration tab settings for ic prog

Verify the following values:
Bits per second: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: none

Test the Programmer

connect the programmer to computerStart the IC Prog softwaredo a preliminary check of the serial interface by selectingSettings?→ Hardware Checkfrom the menu.? The following dialog box will come up:

IC Prog Hardware Check enable clock

Turn on “Enable Clock” by selecting the check box. This will allow the power and LED to be turned On or Off. If this does not work check LED and PIC Programmer Circuit.

Programming the microcontroller using IC Prog,

Select the device (microcontroller) to be programmed. (Settings→ Device)Open the code file (hex file) to be written in the PIC.
Oscillator and Configuration bits are changed as indicated by the *.hex file. We can
maintain these values, or change them later if we have problems during the
programming proccess.Programming the microcontroller,
press Program All button or F5.

IC Prog Program All button

During the programming, some messages will be shown:

Device writing confirmation (if enabled)Programming code progress barProgramming data progress barProgramming configurationVerifying code (if enabled)Verifying data (if enabled)

IC-Prog will show the following dialog box if the verification is successful.

ic prog successfully verified message

PIC Programming is done. Now you can use this PIC IC for your circuit.

If the verification fails, don’t worry, no permanent damage is done. ?There are two common verification failures – data and code. ?A data verification failure can be safely ignored?and just means that the EEPROM was not fully zeroed. ?The message displayed will say “Verify failed at data address XXXXh”. ?Note the word “data” in front of “address”.

ic prog Verify failed at data address XXXXh

If the message says “Verify failed at address XXXXh”, note that the word “data” isnotin front of “address”,?then the code verify failed and there is some sort of problem.

IC Prog Verify failed at address XXXXh message

Errors solutions:

General

Erase the PIC before writing itClose all other applications running on the PC

Hardware

Check the cable connections and the number of the serial portCheck the model of PIC that we are programmingCheck the PIC position on the socketCheck that all the pins are correctly inserted on the socket

Software

Check the type of PIC.Check Menu → Settings → Type of hardware.Check the number of serial port selected.Check that the file code (*.hex) is correct. It’s no good writing a *.txt file in the
PIC.

Other

Change the portUse another PCTry another programmerChange the PIC


Please send your ideas, which are very important for our success…

Share


Reprinted Url Of This Article:
http://www.electronicecircuits.com/circuit-tutorials/ic-prog-programmer-settings-and-programming-pic